CPU BOARD J1 - Power Input (12 pins, .156") 1 - GND 2 - GND 3 - +5V 4 - +5V 5 - Key 6 - Reset Out (unused) 7 - GND 8 - +12V (unused - see note on J6) 9 - +5V 10 - +5V 11 - GND 12 - GND J2 - Inputs IP00 through IP17 (19 pins, .100") 1 - P1 coin 2 - P2 coin 3 - N/C 4 - N/C 5 - Tilt 6 - Test 7 - Service 8 - N/C 9 - GND 10 - P1 Up 11 - P1 Right 12 - P1 Down 13 - P1 Left 14 - Key 15 - P1 Punch 16 - P1 Jump/Start 17 - N/C 18 - N/C 19 - GND J3 - Inputs IP20-IP27, Outputs OP60-OP67, Coin Meter (23 pins, .100") 1 - P2 Up 2 - P2 Right 3 - P2 Down 4 - P2 Left 5 - P2 Punch 6 - P2 Jump/Start 7 - N/C 8 - N/C 9 - GND 10 - Strobe/SIRQ (to SOUNDS GOOD, J1, pin 2) 11 - Sound 0 (to SOUNDS GOOD, J1, pin 4) 12 - Sound 1 (to SOUNDS GOOD, J1, pin 3) 13 - Sound 2 (to SOUNDS GOOD, J1, pin 9) 14 - Sound 3 (to SOUNDS GOOD, J1, pin 8) 15 - Sound Reset (to SOUNDS GOOD, J2, pin 9) 16 - N/C 17 - N/C 18 - GND 19 - Key 20 - Meter Return (to GND on power supply) 21 - Coin Meter 22 - GND 23 - GND J4 - Inputs IP40-IP47, Outputs OP51-OP57 (16 pin, .100") 1 - P3 Up 2 - P3 Right 3 - P3 Down 4 - P3 Left 5 - P3 Punch 6 - P3 Jump/Start 7 - N/C 8 - Key 9 - Stat 0 (to SOUNDS GOOD, J1, pin 6) 10 - GND 11 - N/C 12 - N/C 13 - N/C 14 - N/C 15 - N/C 16 - N/C J5 - Video outputs (9 pins, .100") 1 - Red 2 - GND 3 - Green 4 - GND 5 - Blue 6 - GND 7 - Key 8 - Horizontal sync 9 - Vertical sync J6 - Aux Power Input (11 pins, .100") 1 - GND 2 - GND 3 - +5V 4 - +12V 5 - Key 6 - Reset Out (unused) 7 - Reset Out (unused) 8 - +12V 9 - +5V 10 - GND 11 - GND SOUNDS GOOD BOARD J1 - Sound Selection/Status (9 pins, .100") 1 - Spare (unused) 2 - Strobe/SIRQ (from CPU, J3, pin 10) 3 - Sound 1 (from CPU, J3, pin 12) 4 - Sound 0 (from CPU, J3, pin 11) 5 - STAT1 (unused) 6 - STAT0 (from CPU, J4, pin 9) 7 - Key 8 - Sound 3 (from CPU, J3, pin 14) 9 - Sound 2 (from CPU, J3, pin 13) J2 - Power Input (12 pins, .156") 1 - A GND 2 - A GND 3 - +5V 4 - +5V 5 - +12V 6 - +12V 7 - E GND (unused) 8 - Key 9 - Sound Reset (from CPU, J3, pin 15) 10 - Sound Reset 11 - L GND 12 - L GND J3 - Audio Output (12 pins, .100") - Volume pot "A" and "B" signals go to the two "sides" of the pot. The "wiper" goes in the "middle". 1 - Volume pot wiper (to POT) 2 - Left audio out (to DUAL POWER AMP, J1, pin 2) 3 - Right audio out (to DUAL POWER AMP, J1, pin 3) 4 - A GND (to DUAL POWER AMP, J1, pin 3) 5 - A GND 6 - Audio out (unused) 7 - Audio out (unused) 8 - A GND 9 - Key 10 - Volume pot A (to POT) 11 - A GND 12 - Volume pot B (to POT) J1 - Audio Input (8 pins, .100") 1 - N/C 2 - Left audio 3 - Left shield (from SOUNDS GOOD, J3, pin 4) 4 - Key 5 - GND 6 - Right audio 7 - Right shield (unused) 8 - +12V J2 - Speaker Output (6 pins, .100") 1 - Right speaker +ve 2 - Right speaker -ve 3 - Key 4 - Left speaker +ve 5 - N/C 6 - Left speaker -ve DUAL POWER AMP WITH MIXER J1 - Audio Input (11 pins, .100") 1 - L2 shield (unused) 2 - L2 audio (corresponds to DUAL POWER AMP, J1, pin 2) 3 - L1 audio (unused) 4 - L1 shield (corresponds to DUAL POWER AMP, J1, pin 3) 5 - Key 6 - GND 7 - R2 shield (unused) 8 - R2 audio (corresponds to DUAL POWER AMP, J1, pin 6) 9 - R1 audio (unused) 10 - R1 shield (unused) 11 - +12V J2 - Speaker Output (6 pins, .100") 1 - Right speaker +ve 2 - Right speaker -ve 3 - Key 4 - Left speaker +ve 5 - N/C 6 - Left speaker -ve